我公司提供的产品均为正牌塑胶原料，品质保证，货源稳定，送货上门，可免费提供官方物性表、UL黄卡，并随货提供RoHS报告、SGS报告等，索取权威资料请致电13268582149
ABS MG38F 物性表：
| Physical | Nominal Value | Unit | Test Method |
| Specific Gravity | 1.05 | g/cm³ | ASTM D792 |
| Melt Mass-Flow Rate (MFR) (230°C/3.8 kg) | 3.7 | g/10 min | ASTM D1238 |
| Melt Mass-Flow Rate (MFR) (220°C/10.0 kg) | 15 | g/10 min | ISO 1133 |
| Molding Shrinkage - Flow (3.20 mm) | 0.50 to 0.80 | % | Internal Method |
| Mechanical | Nominal Value | Unit | Test Method |
| Tensile Modulus 2 | 2140 | MPa | ASTM D638 |
| Tensile Strength 3 (Yield) | 43.4 | MPa | ASTM D638 |
| Tensile Strength 3 (Break) | 33.1 | MPa | ASTM D638 |
| Tensile Elongation 3 (Yield) | 2.1 | % | ASTM D638 |
| Tensile Elongation 3 (Break) | 26 | % | ASTM D638 |
| Flexural Modulus 4 (50.0 mm Span) | 2210 | MPa | ASTM D790 |
| Flexural Strength 4 (Yield, 50.0 mm Span) | 68.9 | MPa | ASTM D790 |
| Impact | Nominal Value | Unit | Test Method |
| Notched Izod Impact (23°C) | 370 | J/m | ASTM D256 |
| Instrumented Dart Impact (23°C, Total Energy) | 31.9 | J | ASTM D3763 |
| Thermal | Nominal Value | Unit | Test Method |
| Deflection Temperature Under Load (0.45 MPa, Unannealed, 3.20 mm) | 97.2 | °C | ASTM D648 |
| Deflection Temperature Under Load (1.8 MPa, Unannealed, 3.20 mm) | 82.2 | °C | ASTM D648 |
| Vicat Softening Temperature | 98.9 | °C | ASTM D1525 5 |
| CLTE - Flow (-40 to 40°C) | 0.000088 | cm/cm/°C | ASTM E831 |
| CLTE - Transverse (-40 to 40°C) | 0.000086 | cm/cm/°C | ASTM E831 |
| Electrical | Nominal Value | Unit | Test Method |
| Arc Resistance (PLC) 6 | PLC 5 | ASTM D495 | |
| Flammability | Nominal Value | Unit | Test Method |
| Flame Rating - UL (1.52 mm) | HB | UL 94 | |
| UL | Nominal Value | Unit | Test Method |
| RTI Str | 60.0 | °C | UL 746 |
| RTI Imp | 60.0 | °C | UL 746 |
| RTI Elec | 60.0 | °C | UL 746 |
| Comparative Tracking Index (CTI) (PLC) | PLC 0 | UL 746 | |
| High Voltage Arc Tracking Rate (HVTR) (PLC) | PLC 2 | UL 746 | |
| Hot-wire Ignition (HWI) (PLC) | PLC 3 | UL 746 | |
| High Amp Arc Ignition (HAI) (PLC) | PLC 0 | UL 746 | |
| Fill Analysis | Nominal Value | Unit | Test Method |
| Melt Viscosity (240°C, 1000 sec^-1) | 245 | Pa·s | ASTM D3835 |
